Heat pump or furnace? That is the first thing that matters when the heat quits in Clovis, CA, because the two fail in completely different ways. Heat pumps tend to freeze up when defrost stops working, get stuck in cooling when a reversing valve fails, or quietly lean on the electric backup strips, at several times the normal operating cost, when the outdoor unit dies. Gas furnaces typically come down to the flame sensor: once oxide coats it, the burners light but the flame cannot be proven, so the board cuts the gas and locks out after three tries. After that, the usual suspects are cracked hot surface igniters, stuck pressure switches, clogged condensate traps on high-efficiency models, and blower motors at the end of their life.
Fault codes are where our diagnosis starts, not where it ends. On every no-heat call, Clovis HVAC confirms the board's story with measurements: flame signal read in microamps, igniter resistance checked, the pressure switch tested against real inducer draft, capacitors and motors metered, and, on heat pumps, refrigerant charge and defrost operation verified. Any visit that touches the gas side also covers the safety basics. We leak-test the connections, look over the heat exchanger, and confirm the flue is drafting, since no heating repair is finished until it has been proven safe.
Gas and electric furnaces, heat pumps, air handlers, boilers, and ductless systems from every major brand are all part of our daily work. Because the trucks carry the parts that fail most, including igniters, flame sensors, capacitors, inducer motors, and blower motors, most repairs are done before we leave. When a system has reached the end of its useful life, you will hear that from us plainly, along with real numbers for each option. Need heat back in Clovis? Call (559) 337-5477 and we can get someone to you today.
Most of our service calls are for Furnace Repair in Clovis. Start there if your system isn't running right.
When to Call for Heating Repair in Clovis
Catching these issues early helps you avoid costly problems and protect your property. Here are the most common indicators that it's time to call a professional:
- Strange smells from the vents, especially rotten egg or burning
- Banging at startup caused by burners lighting late
- Thick ice or frost covering the heat pump outside
- Short cycling every few minutes while the house stays cold
- Higher heating bills with less comfort to show for them
- Cold rooms in one part of the house while others are comfortable
- The furnace clicking and trying to light but shutting back down
- Cold air, or no air at all, when the thermostat calls for heat
Act Before It Gets Worse
What seems like a minor issue today can take out a compressor or heat exchanger tomorrow. Don't wait, get Clovis HVAC on the phone at (559) 337-5477 and we'll take a look right away.
Ready to Solve Your Heating Repair Problem?
Call Clovis HVAC for fast, reliable service.
Get Help: (559) 337-5477Frequently Asked Questions About Heating Repair
Why Professional Heating Repair Matters
Heating repair carries more risk than any other job in home comfort work because combustion is involved. A furnace that lights late booms gas vapor inside the heat exchanger and stresses the metal; a heat exchanger that cracks can pass combustion gases into the supply air; a flue that has stopped drafting sends carbon monoxide into the house instead of out of it, and none of these announce themselves in ways an untrained eye can catch. The diagnostic terrain is genuinely tricky too: a furnace that short-cycles might have a failing limit switch, or it might be protecting itself from a clogged filter, and cleaning a flame sensor without asking why it fouled leaves the next lockout already scheduled.
Instruments and judgment are what our experienced technicians bring to both sides of that problem. We measure the flame signal instead of assuming it, inspect the heat exchanger, verify draft at the flue, and check temperature rise against the data plate so the airflow matches the fire. With heat pumps, the defrost board, sensors, and reversing valve get tested before anyone condemns a compressor, and we look at whether the backup strips have been running up your bill for weeks. Every repair we finish is proven safe and correct over a full heating cycle, which is the standard you should expect from anyone working on the equipment that keeps your family warm.
How Our Heating Repair Works
Every visit follows a step-by-step method refined over years of hands-on experience. Here's a look at each step our Clovis HVAC team takes:
Diagnosis & Safety Inspection
Each call begins with measurements, not guesses: flame signal, igniter resistance, pressure switch response, and motor and capacitor health, plus refrigerant charge and defrost on heat pumps. Gas connections are leak-tested as a matter of course.
Straight Answers & a Firm Price
Before any repair begins, we walk you through what broke, why it broke, and what it will cost. And if the findings, like a cracked heat exchanger or a dead compressor, point toward replacement, we say so plainly.
Expert Repair
Most heating repairs wrap up in one trip. The parts that fail most often, including igniters, flame sensors, pressure switches, capacitors, and motors, are already on the truck, so the heat is back on before we head out.
Final Testing
Before we leave, the system runs through full heating cycles while we measure temperature rise against the data plate, confirm safe combustion and venting on fuel-burning equipment, and check each safety control.
Want a Professional Opinion?
We provide honest advice and upfront pricing on all heating repair work.
Call (559) 337-5477 TodayMaintenance Tips for Heating Repair
A little routine maintenance goes a long way toward avoiding a mid-season breakdown. Start with these practical measures our team relies on:
- Have the system serviced each autumn, before the weather tests every weak component
- Make sure every level has a working carbon monoxide detector, and test it monthly
- Never store paints, solvents, or chlorine products near the furnace; their vapors corrode the burners
- Leave open space around the furnace so the burners can draw enough combustion air
- Change the filter monthly in heating season; starved airflow trips limit switches and cracks exchangers early
- Clear snow, leaves, and overgrown shrubs from around the heat pump so defrost works properly
- Do not ignore a boom at ignition or a new rattle, since early repairs cost far less
Should You DIY or Call a Pro?
While some minor tasks like changing filters or checking a thermostat can be handled by homeowners, most HVAC work involves refrigerant, gas combustion, and high-voltage electricity, jobs that call for professional expertise. Consider the following comparison:
| Factor | DIY Attempt | Professional Service |
|---|---|---|
| CO Safety | An unseen hazard never gets tested | Draft and heat exchanger checked every visit |
| Diagnosis | Error code guessing games | Readings taken before parts are replaced |
| Gas Safety | Small leaks slip by undetected | Connections leak-tested with instruments |
| Heat Pumps | Defrost problems misread as total failure | Each defrost component checked in turn |
| Underlying Cause | Symptom treated, problem left behind | The fault behind the fault diagnosed |
| Final Testing | One successful start and done | Temperature rise measured over full cycles |
Talk to a Heating Repair Expert
Don't let a failing system get worse. Call Clovis HVAC now for prompt, professional service.
Call (559) 337-5477 NowHeating Repair Near Clovis
Wherever you are in the area, the same experienced team handles your heating repair. Find your community below.